OptiX RTN Radio Transmission System. VRC Commissioning and Configuration Guide (Web LCT). Issue, Date, HUAWEI. Huawei provides technical support resources for OptiX RTN Series Transmission Network. Access product manuals, HedEx documents, and visio stencils. Huawei provides technical support resources for OptiX RTN A Series Transmission Network. Access product manuals, HedEx documents, and visio stencils.

Author: Goltijora Yozshuran
Country: Grenada
Language: English (Spanish)
Genre: History
Published (Last): 20 August 2017
Pages: 233
PDF File Size: 6.47 Mb
ePub File Size: 15.19 Mb
ISBN: 927-8-55180-857-5
Downloads: 93342
Price: Free* [*Free Regsitration Required]
Uploader: Kashura

Its primary purpose is to suppress alarms being raised at affected higher level client LSPs huawie in turn their client layers. Prerequisite l Hardware installation has been completed and has passed the installation check. As the identifier of a radio link, this parameter is used to prevent incorrect connections of radio links between sites.

RTN 950 V100R005C01 Commissioning Guide 04

Set parameters as follows: High Speed Downlink A modulating-demodulating algorithm put forward in 3GPP R5 to meet the requirement Packet Access for asymmetric uplink and downlink transmission of data services.

Global Positioning A global navigation satellite system. The broadcast range is determined by the broadcast address. It should show that the services are restored after transient interruption. The dialog box that is displayed indicating the operation result is closed. In Check for newer versions of stored pages, huawwei Every visit to the page, and then click OK. The Add Clock Source dialog box is displayed.

It is recommended that you set this parameter to Revertive Mode. The forwarding plane is connection-oriented, and can be used in Layer 2 networks such as an ATM network.

Specifically, if the electric field vector of the electromagnetic wave is perpendicular to the plane of horizon, this electromagnetic wave is called vertically polarized wave; if the electric field vector of the electromagnetic wave is parallel to the plane of horizon, this electromagnetic wave is called horizontal polarized wave; if the tip of the electric field vector, at a fixed point in space, describes a circle, this electromagnetic wave is called circularly polarized wave.


FTP See File Transfer Protocol full-duplex A full-duplex, or sometimes double-duplex system, allows communication in both directions, and, unlike half-duplex, allows this to happen simultaneously. Step 3 In the physical view, select the NE whose time needs to be synchronized, and then click. BE service does not ensure any improvement in delay time, jitter, packet loss ratio, and high reliability.

In Tributary Loopback, select Outloop. On the General tab, click Settings in the Temporary Internet files area.

Then, the configuration interface is displayed. The voltage, pole connection, and fuse current of the power system have been checked in huswei process of connecting power cables. The former is responsible for allocating the label, selecting the route, creating the label forwarding table, creating and removing the label switch path; the latter forwards the labels according to groups received in the label forwarding table.

Huawei OptiX RTN A Support Guide, Manuals & PDF – Huawei

Typically, once a party begins receiving a signal, it must wait for the transmitter to stop transmitting, before replying. Slightly adjust the elevation and azimuth at point 2 as shown in Figure until VBNC reaches the peak within the tracked range.

PDH See plesiochronous digital hierarchy PDU See protocol data unit PE See provider edge peak burst size A parameter used to define the capacity of token bucket P, that is, the maximum burst IP packet size when the information is transferred at the peak information rate. The system displays a dialog box indicating The operation may interrupt the service, are you sure huxwei continue?

Site Commissioning Items Configuring Site Commissioning Data by Using the Handheld Tool Commissioning engineers can configure site commissioning data by using the handheld tool on site when they are: It uses cost as its routing hiawei.

RTN VRC01 Commissioning and Configuration Guide 02(Web LCT) – Huawei

The board indicators should conform to the following states and sequences. When carrying a chassis, the carriers should stretch their kanual and move stably to avoid being strained. This is to prevent the heavy objects on the cabinet top from falling down, which may hurt you. In this manner, the manuql 2 virtual private network VPN is provided for the user. It rth point-to-point QoS guarantees for services transmitted over this domain.


The NE Explorer is displayed. Step 5 Before the switching, query the status of the protection group that is configured on NE A.

In this manner, the spread of the multicast data on layer 2 network can be prevented efficiently. The main and standby radio paths are tested synchronously. Based on the slot layout, the NE automatically configures the logical boards that are required but are not yet configured for certain physical boards. When receiving data, the MAC protocol checks whether the information is correct and whether the data is transmitted correctly.

This topic mainly describes how to test the fiber jumper connection by using an optical interface board. Step 11 Create NEs. Modifying the NE ID does not interrupt services. Outloop A method of looping back the input signals received at a port to an output port without changing the structure of the signals.

Anti-jitter Time 0 to – l When Anti-jitter Time s is not set to 0, a protection group does not report an alarm immediately after it is degraded, but reports the alarm after the specified anti-jitter time expires.

Step 10 Repeat Steps 1 through 7 to check fiber jumper connections of other optical interfaces and then restore the connections when completed.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co.