The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. I have put together the written info on the Align 3GX v I found so far. Mostly for my own memory. I shrunk this info to a Pocket Guide that I will printout (or read.
|Published (Last):||23 October 2008|
|PDF File Size:||4.50 Mb|
|ePub File Size:||4.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
To achieve consistent gyro gain on left and right, 3GX has built in anti-torque compensation function.
3GX Flybarless System – Download – Align
Why does that manual start on alig 20? Push the throttle stick on transmitter to the maximum top, and in a few moments LED will go off and system power cycles, indicating the completion of setup process. Anti-torque To achieve consistent gyro gain on left and right, 3GX has built in anti-torque compensation function. Pay extra attention to these setup steps.
First check how the rudder responds to Tx. I also found this site: Press the SET button to enter E.
What software, this software. Push and hold the SET button for 2 second to enter aljgn rudder gyro setup mode while 3GX is turned on. Subsequent setup mode is entered by a single press of the SET button.
Password Please enter a password for your user account. Set the right aileron and front elevator to 8 degrees. Mannual frame rate must be selected based on your servo’s specifications. While keeping swashplate level and main pitch at zero degrees, press the SET button to register the neutral point and enter E.
aligb Push bind button my spektrum tx module 4. Just leave the servo horns off until your in setup and install them as close to level as poss at mid stick. Tilt the helicopter forward and check if swashplate is tilting correctly toward the back.
3GX manual – HeliFreak
Flight mode settings through 3GX V2 unit. Go to Flybarless System “Direct mode bypassing gyro, for mechanical travel and neutral point setup” to adjust the level of the swashplate and then re-complete the setup. If you use the software there are text and pop-ups to explain the settings: Check if the rudder servo is applying correct compensation to the right.
Due to the high performance gyro sensors used in the 3GX flybarless system, premium high speed digital rudder servos are mandatory for optimal tail performance. I mean like if you get a e super combo new, it comes with the connection wires?
Note that passwords are case-sensitive. REV begin to flash in sequence. Spektrum does make satellites but I am pretty sure they are not in any way compatible.
Tilt the helicopter right as shown in diagramand check if swashplate is tilting correctly toward the left. Tail pitch adjustment First check how the rudder responds to Tx.
The result is a dramatic stability improvement from previous generation, with stability that rivals a flybarred helicopter, yet posses explosive agility. Check that there is no binding throughout the pitch range 3. If needed, servo reverse is done from the transmitter’s REV reverse function.
It is the instructions. Should there be changes such as 3GX software update, pitch reconfiguration, or subtrim adjustments, the setup process must be repeated for the flybarless system.
Flybarless portion of the setup If ava ilable, ensure the following functions are disabled in the transmitter: With all channels stationary, move the transmitter elevator stick forward, and then back to center position.
The superior vibration resistant characteristic is evident even when mounted with harder double sided mounting tape. Faster servos are able to execute commands from the gyro at faster and higher precision. Therefore, BEC output capability should be confirmed to handle burst current when setting collective pitch acceleration, otherwise insufficient current supply may result in flight accidents. Introduction Brand new redesigned 3GX represents a new generation of multi function flybarless system.
This appears to come out of the manual. Does all that stuff pictured in the link come in the kit when you get it new, or is it an aftermarket option? Remove Advertisements Sponsored Links. If ava ilable, ensure the following functions are disabled in the transmitter: Register Now In order to be able to post messages on the HeliFreak forums, you must first register.
In addition, the 3GX can support all of the CCPM swashplate system currently on the market including 90, and degrees swashplates.
Align 3gx pdf manual
Mostly for my own memory. Originally Posted by Tulo I haven’t been able to find the bind procedure, can anyone help me out?? For tail pitch adjustment, center aliggn rudder servo by either setting the 3GX flybarless to normal rate mode non-heading lockor press and hold the SET button for 2 seconds.